No products
Viewed products
-
BS ISO/IEC/IEEE...
BS ISO/IEC/IEEE 8802-15-3:2017...
-
UNE 33112:1975
UNE 33112:1975 TEST METHODS OF...
2021 There are 54665 products.
PPI MS-5 2018
PPI MS-5 2018Model Specification for HDPE Solid Wall Conduitstandard by Plastics Pipe Institute, 04/01/2018
$15.00 $25.00 -40%Reduced price!In stockMaterial Handling Guide (Solid Wall)
Material Handling Guide (Solid Wall)standard by Plastics Pipe Institute, 04/01/2018
$15.00 $25.00 -40%Reduced price!In stockPPI TN-55 2018
PPI TN-55 2018Plastic Piping Materials for Geo Applicationsstandard by Plastics Pipe Institute, 03/01/2018
$15.00 $25.00 -40%Reduced price!In stockPPI TR-41 2018
PPI TR-41 2018Generic Saddle Fusion Joining Procedure for Polyethylene Gas Pipingstandard by Plastics Pipe Institute, 2018
$15.00 $25.00 -40%Reduced price!In stockPPI TR-3 2018
PPI TR-3 2018Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Hydrostatic Design Stresses (HDS), Pressure Design Basis (PDB), Strength Design Basis (SDB), Minimum Required Strength (MRS) Ratings, and Categorized Required Strength (CRS) for Thermoplastic Piping Materials or Pipe...
$15.00 $25.00 -40%Reduced price!In stockPPI TR-2 2018
PPI TR-2 2018PPI PVC Range Composition Listing of Qualified Ingredientsstandard by Plastics Pipe Institute, 2018
$15.00 $25.00 -40%Reduced price!In stockPPI MAB-3
PPI MAB-3Model Specification for PE 4710 Buried Potable Water Service, Distribution and Transmission Pipes and Fittingsstandard by Plastics Pipe Institute, 11/01/2017
$15.00 $25.00 -40%Reduced price!In stockPPI MS-4 2017
PPI MS-4 2017Model Specification For Polyamide 11 (PA-11) Plastic Pipe, Tubing and Fittings for Fuel Gas Distribution Systemsstandard by Plastics Pipe Institute, 10/01/2017
$15.00 $25.00 -40%Reduced price!In stockPPI TN-54 2017
PPI TN-54 2017General Guidelines for Squeezing Off Polyethylene Pipe in Water, Oil and Gas Applicationsstandard by Plastics Pipe Institute, 07/01/2017
$15.00 $25.00 -40%Reduced price!In stockPPI TR-4 2017
PPI TR-4 2017PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipestandard by Plastics Pipe Institute, 06/20/2017
$15.00 $25.00 -40%Reduced price!In stockPPI TN-49 2017
PPI TN-49 2017Recommendations for AWWA C901 Service Tubes in Potable Water Applicationsstandard by Plastics Pipe Institute, 06/01/2017
$15.00 $25.00 -40%Reduced price!In stockPPI TN-52 2017
PPI TN-52 2017Guide to PEX High Temp Ratingsstandard by Plastics Pipe Institute, 06/01/2017
$15.00 $25.00 -40%Reduced price!In stock
