No products
Viewed products
-
DIN ISO 8132:2017-12
DIN ISO 8132:2017-12 Hydraulic fluid...
-
AS 3772:2020
AS 3772:2020...
2023 There are 165 products.
ASME BPVC 2023 Section II part D (metric)
next ordered by strengthfirst tensile strength and thenyield strength. Finally, for a given UNS number, tensilestrength, and yield strength, stress lines are ordered byincreasing specification number. Again, some materialsmay have two or more stress lines even if their UNS number,tensile strength, yield strength, and specificationnumber are the same. The...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section IV
PART HGGENERAL REQUIREMENTS FOR ALLMATERIALS OF CONSTRUCTIONARTICLE 1SCOPE AND SERVICE RESTRICTIONSHG-100 SCOPEa The rules of Part HG apply to steam heating boilers,hot water heating boilers, hot water supply boilers, and toappurtenances thereto. They shall be used in conjunctionwith the specific requirements in Part HF boilers ofwrought materials, Part...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section IX
NONMANDATORY APPENDIX LWELDERS AND WELDING OPERATORS QUALIFIEDSIMULTANEOUSLY TO EN ISO 9606-1, ISO 14732,AND SECTION IX ð23L-100 INTRODUCTIONWhen a welder or a welding operator welds a testcoupon or makes a production weld, that person doesnot weld one way when the applicable standard isASME and another way when the applicable standardis AWS, EN, JIS, or...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section IX
NONMANDATORY APPENDIX LWELDERS AND WELDING OPERATORS QUALIFIEDSIMULTANEOUSLY TO EN ISO 9606-1, ISO 14732,AND SECTION IX ð23L-100 INTRODUCTIONWhen a welder or a welding operator welds a testcoupon or makes a production weld, that person doesnot weld one way when the applicable standard isASME and another way when the applicable standardis AWS, EN, JIS, or...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Code Cases Boilers and...
Approval Date: June 23, 2005Code Cases will remain available for use until annulled by the applicable Standards Committee.Case 1325-18Nickel-Iron-Chromium Alloys 800 and 800H UNSN08800 and N08810 and Nickel-Iron-Chromium-Molybdenum-Copper Low-Carbon Alloy UNS N08028Section IInquiry: May Nickel-Iron-Chromium Alloys 800 and800H UNS N08800 and N08810 and...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section I
MANDATORY APPENDIX VIESTABLISHING GOVERNING CODE EDITIONS, ADDENDA, ANDCASES FOR BOILERS AND REPLACEMENT PARTSVI-1 GENERALAfter Code revisions are approved by ASME, they maybe used beginning with the date of issuance shown on theCode. Except as noted below, revisions become mandatory6 months after the date of issuance. Code Cases are permissibleand may be...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section II part A-1
ASME BPVC.II.A-2023 SA-409/SA-409M689SUPPLEMENTARY REQUIREMENTSOne or more of the following supplementary requirements shall apply only when specified in thepurchase order. The purchaser may specify a different frequency of test or analysis than is providedin the supplementary requirement. Subject to agreement between the purchaser and manufacturer,retest...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section II part A-2
SA-451/SA-451M ASME BPVC.II.A-20237507.2 It is realized that the foundry may be unable to performthe hydrostatic test prior to shipment, or that the purchaser maywish to defer testing until additional work has been performedon the casting. In such cases, the foundry is responsible for thesatisfactory performance of the casting when it is tested.8....
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section II part B
SB-584 ASME BPVC.II.B-2023838Specification forCopper Alloy Sand Castings for General Applications1. Scope1.1 This specification covers requirements for copper alloysand castings for general applications. Nominal compositionsof the alloys defined by this specification are shown in Table1. This is a composite specification replacing former documentsas shown...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section II part C
ASME BPVC.II.C-2023 SFA-5.31M/SFA-5.319272.1 American Welding Society AWS documents:1 AWS A3.0M/A3.0, Standard Welding Terms and Definitions, Including Terms for Adhesive Bonding, Brazing,Soldering, Thermal Cutting, and Thermal Spraying2 AWS A5.01M/A5.01 ISO 14344 MOD, Welding and Brazing ConsumablesProcurement of Filler Metals andFluxes ISO 14344: 2010...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section II part D (metric)
next ordered by strengthfirst tensile strength and thenyield strength. Finally, for a given UNS number, tensilestrength, and yield strength, stress lines are ordered byincreasing specification number. Again, some materialsmay have two or more stress lines even if their UNS number,tensile strength, yield strength, and specificationnumber are the same. The...
$369.37 $859.00 -57%Reduced price!In StockASME BPVC 2023 Section IV
PART HGGENERAL REQUIREMENTS FOR ALLMATERIALS OF CONSTRUCTIONARTICLE 1SCOPE AND SERVICE RESTRICTIONSHG-100 SCOPEa The rules of Part HG apply to steam heating boilers,hot water heating boilers, hot water supply boilers, and toappurtenances thereto. They shall be used in conjunctionwith the specific requirements in Part HF boilers ofwrought materials, Part...
$369.37 $859.00 -57%Reduced price!In Stock
